Home > Emergency Response, SAR, UAVs > Mavic Pro kit for search and rescue operations

Mavic Pro kit for search and rescue operations

I am assisting a local agency with developing a SAR UAV program. Among other things, we will develop use cases and their attendant requirements to drive platform selection but for the moment we’re using DJI Mavic Pros.

What follows is my working UAV SAR kit built around the Mavic Pro.

IMG_2635 (1)

Each component of the kit will be discussed in more detail below. Clockwise from the upper left we have:

  1. Lightweight HDMI external monitor, USB or 12V DC powered
  2. Microsoft Surface Pro
  3. Molle water bottle carrier (repurposed as a Mavic carrier)
  4. Semi-hard shell Mavic case
  5. Dedicated phone, external battery, cables, and spare props
  6. Dual radio harness with type approved VHF radio, type approved air band radio, GPS
  7. Rapid parallel battery charger, 12V “cigarette lighter” charger

 

External data viewing and processing

IMG_2639 (1)

The kit includes a Microsoft Surface Pro running Windows 10. It doesn’t really have enough power to run Pix4D (for example) but it is sufficient for some in-field image processing. It can also run Mission Planner for PixHawk enabled UAVs and can serve as a backup data storage device.

The item on the left is a very inexpensive, lightweight, USB powered HDMI screen. The Surface Pro drives it quite well. We need to determine is the Mavic controller can.

Molle Mavic carrier

IMG_2640 (1)

This is a molle water bottle carrier with a large semi-padded main compartment, a zippered front pouch, and a zippered lower pouch. The Mavic Pro fits snugly in the main compartment with room for a spare battery below it in that compartment. A second spare battery fits in the lower zippered compartment. Cables, phone, and other small items fit in the front compartment. There is no room for the controller but we will attach another molle bag to the side of this carrier to hold the controller.

This would be the bare minimum kit and could be strapped to other gear or carried on its own.

Semi-hard shell Mavic case

IMG_2636 (1)

There are lots of Mavic cases out there. We went with this one because it has room for three spare batteries, the foam is laser cut rather than pick and pull, and the case is semi-rigid.

We also added prop clips (white item over Mavic) to hold the props in place when using the molle carrier, a controller stick guard (lower right, black) to keep the sticks from moving or being damaged when not in use, and a phone mount that moves the phone above the controller and allows for phones in hard cases to be used.

Dedicated phone, external battery, cables, and spare props

IMG_2641 (1)

All SAR flight operations must use a dedicated mobile device rather than a personally owned device. This limits exposure to malware, keeps potential evidence on a device owned by the organization, and provides for consistency across kits. This happens to be a Galaxy 8, chosen for maximum screen brightness.

Also included here are an external battery for recharging the phone, a charger for the phone, spare props, and spare cables.

Dual radio harness, radios, GPS

IMG_2637 (1)

The UAV operator needs to be able to communicate with others involved in the response and also with other manned and unmanned aerial assets. The kit includes a type approved VHF radio for response communications and a type approved air band radio for air operations. (The pilot program lead operator has a ham license (not required for this equipment) and manned aircraft ratings.)

Also included is a GPS unit. The team normally uses Garmin Alpha 100’s which automatically transmit on MURS frequencies to enable base to track assets in the field. To limit potential sources of interference, this GPS unit is passive and does not broadcast.

Rapid parallel battery charger, 12V “cigarette lighter” charger

IMG_2638 (1)

The standard Mavic battery charger is serial – it charges one battery, then the next, then the next. Charging three batteries can take upward of four hours. This charger will charge three batteries and the remote controller in parallel, dramatically improving available flight time.

The stock 12V cigarette charger is included to go out with the molle carrier kit.


 

And that is the working draft of our basic Mavic Pro SAR kit.

Questions, comments, and feedback are most appreciated.

 

Categories: Emergency Response, SAR, UAVs
  1. Mike
    August 3, 2018 at 6:44 am

    Only things missing with this config (albeit, will need a little more storage space) is an omnidirectional amped antenna. I fly quite a bit in the Vermont woods and I use Titan’s Cyclone including the whip antenna’s. Makes a HUGE difference and allows me to lower closer to the ground maintaining a good video and RC signal.

    • August 3, 2018 at 7:42 am

      Absolutely agreed. I was trying to minimize the gear required to operate but I think that identifying various components that might be required depending on use cases makes a lot of sense.

  1. August 3, 2018 at 5:56 am

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: